Nickel differs from the other bulk metals in a way that changes the recycling argument. Steel and aluminium are climate problems because of tonnage, about 3.7 and 1.0 gigatonnes of CO2
per year respectively. Primary nickel production is about 3.5 million tonnes per year at a global average intensity near 20 tonnes CO2 per tonne of metal, which gives of order 70 million tonnes
annually, roughly 2 percent of the steel figure [1,2]. Per kilogram, though, nickel is among the most intensive metals produced. Reported values span 3 to 7 tonnes CO2 per tonne for rich sulfide
feeds treated with low-carbon power, up to 35 tonnes and beyond for laterite routes running on coal-fired electricity [1,6,7]. Life cycle comparisons put sulfide flash smelting with Sherritt Gordon
refining at about 114 MJ per kilogram and 11.4 kg CO2 equivalent per kilogram under coal-based power, with the laterite pressure acid leaching, solvent extraction and electrowinning route higher
again, of order 160 MJ per kilogram [4,5]. Roughly 60 percent of these are direct on-site emissions and only about 15 percent are purchased electricity, so decarbonising the grid does not by itself
decarbonise nickel [1].
The case for nickel circularity therefore rests less on aggregate carbon than on intensity, ore trajectory, water and residue burden, supply concentration, and one structural fact with
no analogue in the steel or aluminium discussion. Nickel is almost never used as a metal. It is used as an alloying element, in stainless steel, superalloys, plating, catalysts and battery cathodes,
and its function is destroyed the moment it is diluted into a matrix that does not need it. More than two thirds of mined nickel goes into stainless steel. Batteries took under 8 percent a decade
ago, take roughly 15 percent now, and are projected above 25 percent by 2030 [1,3,14]. Reported end-of-life recycling rates cluster between 50 and 70 percent and recycled content between 25 and 40
percent, the spread reflecting whether stainless scrap is counted as nickel recycling at all [9,10]. About 70 percent of nickel in post-consumer scrap is recovered, roughly 15 percent disperses into
the carbon steel loop, and a comparable fraction, reported near 17 percent, is lost to landfill in small metal goods and electronic waste; the figures overlap because the accounting boundaries differ
[1].
Two ore families, and the chemistry they impose on recycling
Nickel has no single extractive metallurgy because it has two fundamentally different mineral hosts. In sulfides it occupies a discrete phase, pentlandite, (Fe,Ni)9S8, associated with
pyrrhotite and chalcopyrite. Because the nickel is in its own mineral, physical beneficiation works: crushing, grinding and froth flotation raise a 0.5 to 2.5 wt.% Ni ore to a 6 to 12 wt.% Ni
concentrate, and only that concentrate is smelted [11,12]. In laterites the nickel is not in a discrete mineral at all. Ni2+ substitutes for Fe3+ in the goethite lattice of the limonite horizon and
for Mg2+ in serpentine and garnierite hydrosilicates of the saprolite horizon. There is nothing to float, the carrier phases are fine-grained and intergrown, and the entire ore must be reduced or
leached [1,12]. That single crystal-chemical difference explains why laterite processing is energy intensive, why it now dominates supply as sulfide deposits deplete, and why the associated burdens
are large: 1100 to 1500 litres of water per tonne of sulfide ore against up to 4500 litres for laterite, and up to 2.5 GJ per tonne of sulfide ore against 8 GJ per tonne of laterite [1,6].
The pyrometallurgical laterite route exploits a redox selectivity that is worth stating explicitly, because the same principle governs several recycling flowsheets. NiO is far less
stable than FeO, so under a controlled oxygen potential nickel reduces before iron. The reductant addition in a rotary kiln therefore sets the Ni to Fe ratio of the product rather than the yield
alone, and the process is best understood as selective reduction followed by melting, not as bulk reduction [12,57]. Laterites carry 35 to 40 wt.% water, so drying and calcination kilns tens of
metres long precede the electric furnace, which operates at 1300 to 1600 degrees C because the magnesia and silica content raises the liquidus. The product is ferronickel at 20 to 40 wt.% Ni or
nickel pig iron at 5 to 15 wt.% Ni, refined only to remove silicon, carbon and phosphorus [1,13]. This is class 2 nickel, below 99 percent purity, and it is tied to stainless steel by its iron
content.
The hydrometallurgical route is selected by magnesia. Pressure acid leaching at 245 to 270 degrees C and up to 5.4 MPa in titanium-clad autoclaves dissolves nickel and cobalt but also
magnesium, so acid consumption scales with the MgO content and the process is economic only on low-magnesia limonite. High-magnesia saprolite goes to smelting instead [1,5,11]. The Caron alternative,
reduction roast followed by ammonia and ammonium carbonate leaching, works on a different lever entirely: nickel and cobalt form stable hexammine complexes in solution while iron does not, so the
separation is coordination-chemical rather than redox-chemical. The same ammine chemistry reappears in the Sherritt ammonia pressure leach of sulfide matte, where nickel is recovered from solution by
hydrogen reduction and sulfur leaves as ammonium sulfate, and again in modern battery recycling [11,33]. Recognising that a single selectivity principle runs across primary and secondary nickel
metallurgy is more useful than treating recycling as a separate discipline.
The commercial consequence is the class divide. Battery-grade nickel sulfate requires class 1 metal at 99.8 percent purity or better, with individual metallic impurities specified at
or below about 10 ppm, while most new supply is class 2. Class 1 output has been projected to grow by less than 1 percent per year to 2040, and producers have responded by converting nickel pig iron
and matte into dissolvable intermediates that can enter the sulfate chain, at a substantial carbon cost [1,14]. This mismatch between the chemical form in which nickel is produced and the form in
which it is consumed is one of the strongest arguments for recovering nickel from streams that are already close to the required chemistry.
The stainless loop, and the one-way leak into carbon steel
Stainless steel is the closest thing to a functioning closed metal loop at industrial scale. More than 90 percent of stainless is returned at end of life and essentially all production
scrap is recycled, and because the scrap carries chromium, nickel and molybdenum, remelting it avoids roughly 4.5 tonnes of CO2 per tonne of stainless scrap relative to producing those elements from
ore [1]. With about 60 million tonnes of stainless melted annually, scrap charges near half of that, and 8 to 10 wt.% Ni in the austenitic grades, the nickel units circulating in this loop are of
order one million tonnes per year, comparable to a third of primary supply [15]. Sorting is assisted by a physical property that most alloy systems lack: ferritic chromium stainless steels are
ferromagnetic and austenitic chromium-nickel grades are not, so magnetic separation gives a coarse alloy-family split before any spectroscopy is applied. Nickel accounts for 70 to 80 percent of the
price of austenitic stainless, and stainless scrap trades between about 1000 and 2500 EUR per tonne, which is why this loop closed on economics long before it was justified on carbon [1,23].
The leak is thermodynamic. Nickel is nobler than iron, so it cannot be oxidised into slag during electric arc furnace or converter operation. Chromium, which is less noble, oxidises
and is largely lost to the slag, contaminating a residue that then has restricted downstream use. Nickel survives and reports to the steel [16]. The result is a one-way valve from stainless and
heat-resistant steel scrap into the carbon steel pool, where nickel typically accumulates at 0.05 to 0.2 wt.% and rises as the mixed post-consumer fraction grows [20,21]. Multi-life-cycle tracking
with alloy-resolved material flow models shows this dissipation clearly: chromium is lost mainly to slag, nickel mainly to dilution, and neither is recovered as an alloying element once the streams
mix [17]. Where steels are mixed indiscriminately the effective loss of alloying value reaches 93 percent; parts-based sorting before shredding can retain 94 to 98 percent of the contained manganese,
chromium, nickel and molybdenum [18,19].
Nickel in carbon steel is not damaging in the way copper is. It causes no hot shortness, and it actively mitigates copper-induced hot shortness by raising the solubility of copper in
austenite, so the Ni to Cu ratio, not the absolute nickel content, is the controlling parameter during reheating and hot rolling [16,29]. But nickel is metallurgically active, and this is where a
steel metallologist must be quantitative. In the Andrews relation the martensite start temperature falls by 17.7 degrees C per wt.% Ni, alongside 30.4 per wt.% Mn and 423 per wt.% C, so residual
nickel lowers Ms and Mf, raises hardenability, widens the transformation-inert region and shifts continuous cooling behaviour [22]. It also enters the weldability constraint through the carbon
equivalent, CE = C + Mn/6 + (Cr+Mo+V)/5 + (Ni+Cu)/15, so nickel that is metallurgically welcome in the base metal can still push a plate outside its heat-affected-zone hardness limit [16].
Nickel-bearing carbon steel is therefore best described as downcycled rather than poisoned: the element retains some function, but the value paid for it as class 1 nickel is gone.
There are deliberate sinks, and they should be assessed by tonnage rather than by elegance. Cryogenic grades use nickel intentionally, 3.5 wt.% for low-temperature service and 9 wt.%
for LNG containment, and nickel is a strong austenite stabiliser and retained-austenite promoter in TRIP and quenching and partitioning steels. Austenitic Ni-resist cast irons take 14 to 36 wt.% Ni.
In the ferrous casting loop, nickel arrives with stainless and alloy steel scrap and appears among the twenty or more residual elements tracked in 100 percent scrap ductile iron production, where it
stabilises pearlite and strengthens ferrite [24]. None of these outlets is large enough to absorb the nickel entering the carbon steel pool, exactly as weathering steels cannot absorb the copper. The
general lesson is that a sink alloy must be evaluated against the mass flow of the contaminant, not against its metallurgical suitability.
Nickel that leaves the alloy loop
Outside stainless and superalloys, nickel is dispersed in products from which it must be re-separated element by element. Nickel-metal hydride packs from hybrid vehicles contain of
order 30 wt.% nickel, split between the Ni(OH)2 positive electrode and the AB5 mischmetal-nickel negative electrode, and they represent one of the few chemically concentrated nickel scrap streams
outside the steel loop [36]. Spent hydroprocessing catalysts carry 2 to 6 wt.% Ni with 8 to 20 wt.% Mo and up to 15 wt.% V on alumina, and their management combines decoking roasting, soda roasting
to convert molybdenum and vanadium into water-soluble salts, and either acid leaching or smelting of the nickel-bearing residue [35]. Electroplating sludges, pickling liquors, grinding swarf and
spent Ni-Cd cells belong to the same category. In printed circuit boards nickel appears mainly as the internal electrodes of multilayer ceramic capacitors, layers well below one micrometre thick, and
as connector plating, which places it firmly in the nanoscrap regime where physical liberation fails and only chemical routes remain [38].
Lithium-ion batteries will dominate the growth. At roughly 0.6 to 0.7 kg of nickel per kWh for high-nickel layered oxide cathodes, a 100 kWh pack contains 60 to 70 kg of nickel, and of
order one million traction packs are projected to reach end of life by 2030 [1,25,26]. The metallurgy of recovering it divides cleanly. In pyrometallurgical treatment, nickel, cobalt and copper
reduce together into an Fe-Ni-Co-Cu alloy while lithium, manganese and aluminium oxidise into the slag; the process concentrates but does not separate, and the alloy must be leached anyway [25].
Hydrometallurgical treatment dissolves the black mass in sulfuric acid with hydrogen peroxide. The peroxide is a reductant here, not an oxidant: nickel and cobalt are trivalent in the layered oxide
and must be reduced to the divalent state to dissolve, which is why the leach is written as a reductive rather than an oxidative step [29,30]. Iron and aluminium are removed by pH-controlled
hydrolysis, copper by cementation or sulfide precipitation, manganese by oxidative precipitation or extraction.
The nickel-cobalt separation is the hardest step and the most instructive. The two elements are adjacent, both divalent in solution, with similar ionic radii and similar hydrolysis
behaviour, so separation cannot rely on redox or on basicity. It relies on coordination geometry. Organophosphoric extractants such as D2EHPA give cobalt over nickel separation factors of order 10,
the alkylphosphonic PC88A of order 50 to 100, while the sterically hindered phosphinic acid Cyanex 272 reaches 1000 and above because Co2+ readily forms a tetrahedral complex with the bulky ligand
while the more strongly hydrated Ni2+ does not [31,32]. This is a design decision at the molecular scale that determines whether a battery recycler can produce battery-grade sulfate at all.
Ammoniacal routes offer the alternative: reductive ammonia leaching with sodium sulfite dissolves nickel and cobalt as ammine complexes and leaves manganese, iron and aluminium behind, closing the
same chemical loop that the Caron process opened a century ago [33]. Carbonyl refining is the third option and the most selective of all. Ni(CO)4 forms near atmospheric pressure at 50 to 80 degrees C
and decomposes above about 180 to 200 degrees C, while cobalt does not form a volatile carbonyl under those conditions, so the transport reaction separates nickel from cobalt and from most
non-carbonyl-forming impurities. Its use is confined to dedicated plants because nickel tetracarbonyl is acutely toxic and volatile [11].
Direct cathode recycling raises a different class of question, one that is crystal-chemical rather than extractive. In layered LiNixMnyCozO2 the ionic radii of Ni2+ and Li+ are 69 and
76 pm, close enough that nickel occupies lithium sites, producing antisite mixing that blocks lithium diffusion. High-nickel compositions are more prone to this, to surface reconstruction into
rock-salt NiO, and to intergranular microcracking, all of which are the degradation modes that end first life [27,28]. Restoring the material therefore requires relithiation followed by annealing in
oxygen to reoxidise Ni2+ to Ni3+ and re-establish cation ordering, not merely a chemical top-up of lithium [34]. There is also a donor-acceptor mismatch that the recycling literature has begun to
address directly: the cathodes returning as scrap are NMC532 and NMC622, while demand has moved to NMC811 and, in a large share of the market, to lithium iron phosphate, which contains no nickel at
all. Upcycling the composition during relithiation, by adding nickel to the recovered precursor, is a genuine alloy design problem inside a ceramic. It also illustrates the boundary of
impurity-tolerant design: the approach that works for structural alloys does not extend to battery-grade sulfate at 10 ppm impurity limits, where trace contamination is not tolerated but eliminated
[24].
Alloy design: substitution, tolerance and designed sinks
Three distinct strategies are usually conflated under nickel recycling, and they have different consequences.
Substitution reduces demand for primary nickel. Nitrogen is the most powerful lever available in stainless steel: in the nickel equivalent, Ni_eq = Ni + 30(C+N) + 0.5Mn, each 0.1 wt.%
N substitutes for about 3 wt.% Ni in austenite stabilisation, which is the basis of the high-nitrogen austenitic grades produced by pressurised melting [46]. Manganese substitutes at 0.5 the
effectiveness of nickel and is the basis of the 200 series. In structural steels the same logic has produced lean medium-manganese concepts and an Fe-18Mn-3Ti maraging steel that reaches ultrahigh
strength through segregation-assisted alpha-Mn nanoprecipitation without nickel, cobalt or molybdenum [43,44,45].
The circularity paradox is that these substitutions can be counterproductive when evaluated correctly. Nickel in austenitic stainless is already circulating at 90 percent end-of-life
return through a well-established, high-value scrap loop. Replacing it with manganese interrupts that loop, introduces a new contaminant into stainless scrap, and devalues a material trading at 1000
to 2500 EUR per tonne [1,45]. The relevant comparison is marginal, not average: primary nickel carries about 20 tonnes CO2 per tonne, whereas nickel already reduced and circulating in scrap carries a
marginal footprint close to zero. An element that appears unsustainable when won from ore can be the more sustainable choice once it exists in metallic form inside a functioning loop. Substitution
decisions must therefore be made against the state of the scrap system, not against a table of embodied energies.
Tolerance is the second strategy, and for nickel-base alloys it means something specific, because here nickel is the matrix and the question is what can be removed from it. The
nobility rule that governs steel and copper applies again with a different cast. In a nickel melt, aluminium, titanium, silicon, manganese and chromium can be oxidised out under vacuum or controlled
oxygen potential; iron, cobalt, molybdenum, tungsten, rhenium, niobium and tantalum cannot be separated economically, and cobalt in particular is essentially irremovable because its oxide stability
is adjacent to that of nickel [40,41]. Superalloy recycling is therefore revert management, not refining. The practical rules are short:
- Sort revert by grade before melting, since cobalt, rhenium, tungsten and niobium cannot be corrected afterwards and their specifications differ by several weight percent between
alloys.
- Control the elements that do segregate rather than those that do not dissolve: sulfur, phosphorus, lead, bismuth, selenium, tellurium and silver at ppm levels decorate grain boundaries
and destroy creep ductility, and they are not removed by ordinary oxidation refining [40,42].
- Keep oxygen, nitrogen and hydrogen within specification through vacuum induction melting and, where required, electroslag or vacuum arc remelting, since the strengthening gamma prime
phase is sensitive to the reactive-element balance.
- Segregate machining chips and grinding swarf by coolant and tool type, because oxidation and iron pickup during machining, not alloy chemistry, are what disqualify most aerospace revert
[39,42].
The economic leverage here is real. Investment casting generates large runner and riser returns, machining removes most of the input mass in some aerospace parts, and life cycle
assessment of aerospace alloy recycling shows substantial carbon benefits from keeping these streams inside their own alloy family [39].
The third strategy is to design sinks in other metal systems for the nickel that has already escaped. In aluminium, nickel is nobler than the base metal and cannot be oxidised out, and
it forms Al3Ni; but controlled nickel additions have been shown to modify the morphology of iron-bearing intermetallics in high-iron recyclable Al-Si cast alloys, turning one contaminant into a
corrector for another [47,48]. In copper the situation is stricter. Cu-Ni is isomorphous with complete solid solubility, so nickel cannot be gettered into precipitates by aging. Atom probe analysis
of recycled battery copper found essentially all of the 0.26 wt.% Ni retained in the matrix after annealing, contributing about 0.3 micro-ohm cm, roughly 12 percent of the measured resistivity, at a
coefficient near 1.2 micro-ohm cm per at.% [49]. The only metallurgical answer inside the copper system is to add silicon and precipitate delta-Ni2Si, which is precisely what Corson-type Cu-Ni-Si
alloys such as C70250 do, reaching 700 to 900 MPa at 40 to 50 percent IACS [50]. Matching a contaminant to an alloy family that consumes it is more durable than diluting it.
Process innovation may relax some of these constraints. Selective sulfidation separates chemically similar transition metals, including nickel and cobalt, by tuning sulfur and oxygen
chemical potentials rather than aqueous pH, and molten sulfide electrolysis can then deposit metal while evolving elemental sulfur instead of SO2 [51]. Molten oxide electrolysis with inert anodes
offers an oxide-side equivalent for nickel-bearing slags and residues [52]. Hydrogen plasma reduction of nickel oxide is thermodynamically favourable at modest temperature because NiO sits high in
the Ellingham ordering, and cold plasma routes have been demonstrated for nickel production, which makes nickel one of the easier metals to decarbonise by hydrogen [53]. Reductive bioleaching attacks
the specific problem of laterite crystal chemistry: acidophilic iron reducers dissolve the goethite host and release lattice-bound nickel and cobalt at ambient temperature, a route now being extended
to nickel-bearing residues and secondary wastes [54,55,56,37]. Reduction roasting followed by magnetic separation upgrades limonitic feeds by exploiting the same selective-reduction principle as the
smelter, but at lower temperature [57,58], and solvometallurgical routes reduce water consumption in streams where aqueous chemistry is poorly selective [59].
Data-driven design is beginning to handle the combinatorics. In the ferrous casting demonstration, more than twenty residual elements including nickel enter with stainless and alloy
steel scrap, and a surrogate-model tree search over composition, processing and microstructure identified 100 percent scrap formulations that improved both strength and ductility [24,63]. The
framework transfers in principle to nickel-bearing systems, but its accuracy is bounded by the representativeness of the training data, and extrapolation errors grow outside the sampled window. For
nickel the more immediate use is flowsheet and charge-blend optimisation under variable scrap chemistry rather than the discovery of new physics.
Competing primary sources should be judged against this background. Polymetallic nodules carry 1.2 to 1.5 wt.% Ni with about 1 wt.% Cu and 0.2 wt.% Co in a manganese oxide matrix, and
demonstrated flowsheets reduce them to an Fe-Ni-Cu-Co-Mo metal phase with a manganese-rich slag that is subsequently re-smelted, followed by ion exchange, solvent extraction and electrowinning
[60,61]. Fungal leaching of the same feed has recovered more than 80 percent of the nickel, copper and manganese [62]. These are genuine resources, but they are new primary supply with new
environmental burdens, and the same co-extraction requirement applies: a process that recovers only nickel and cobalt and discards manganese, iron and silicon reproduces the residue problem that
recycling is meant to avoid.
The limits should be stated plainly. Stainless steel returns after 20 to 50 years and traction batteries after 10 to 15, so the nickel now entering service will not be available as
feedstock until the 2030s and beyond. Battery chemistry is moving faster than the scrap it generates, and a growing lithium iron phosphate share means that some of the nickel demand projected today
will not exist when the corresponding scrap arrives. Nickel dissipated in coatings, lost by catalyst attrition, or diluted into carbon steel is not recoverable by any foreseeable process. The
measurable gaps are specific: multicomponent thermodynamics and kinetics of the Ni-Co-Mn-Fe-Cu-Mg-S-O system under recycling conditions; grain boundary segregation isotherms of sulfur, phosphorus,
bismuth and lead in nickel at the ppm level and their effect on creep ductility; carbonyl and sulfidation kinetics on mixed, contaminated feeds rather than on pure compounds; extractant degradation
and organic losses in long campaigns; and allocation rules for open-loop recycling, without which the carbon benefit of stainless scrap entering carbon steel cannot be assigned honestly [21,38,64].
Closing these gaps determines whether nickel remains a metal that is recycled by accident, inside a steel loop that does not value it, or one that is deliberately kept functional across the alloys
that actually need it.
References
- Raabe, D. The materials science behind sustainable metals and alloys. Chemical Reviews 123 (2023) 2436-2608.
- US Geological Survey. Mineral Commodity Summaries: Nickel (2025).
- International Energy Agency. The Role of Critical Minerals in Clean Energy Transitions (2021).
- Norgate, T. E., Jahanshahi, S., Rankin, W. J. Assessing the environmental impact of metal production processes. Journal of Cleaner Production 15 (2007) 838-848.
- Norgate, T. E., Jahanshahi, S. Assessing the energy and greenhouse gas footprints of nickel laterite processing. Minerals Engineering 24 (2011) 698-707.
- Mudd, G. M. Nickel sulfide versus laterite: the hard sustainability challenge remains. CSIRO Minerals Down Under (2009).
- Wei, W., Samuelsson, P. B., Tilliander, A., Gyllenram, R., Jonsson, P. G. Energy consumption and greenhouse gas emissions of nickel products. Energies 13 (2020) 5664.
- Elshkaki, A., Reck, B. K., Graedel, T. E. Anthropogenic nickel supply, demand, and associated energy and water use. Resources, Conservation and Recycling 125 (2017) 300-307.
- Reck, B. K., Graedel, T. E. Challenges in metal recycling. Science 337 (2012) 690-695.
- Graedel, T. E., Allwood, J., Birat, J. P., et al. What do we know about metal recycling rates? Journal of Industrial Ecology 15 (2011) 355-366.
- Crundwell, F. K., Moats, M. S., Ramachandran, V., Robinson, T. G., Davenport, W. G. Extractive Metallurgy of Nickel, Cobalt and Platinum Group Metals. Elsevier (2011).
- Warner, A. E. M., Diaz, C. M., Dalvi, A. D., Mackey, P. J., Tarasov, A. V. JOM world nonferrous smelter survey, part IV: nickel laterite. JOM 59 (2007) 58-72.
- Zevgolis, E. N., Daskalakis, K. A. The nickel production methods from laterites and the Greek ferronickel production among them. Materials Proceedings 5 (2022) 104.
- Fraser, J., Anderson, J., Lazuen, J., et al. Study on future demand and supply security of nickel for electric vehicle batteries. Publications Office of the European Union (2021).
- worldstainless (International Stainless Steel Forum). Stainless steel melt shop production and recycling statistics (2024).
- Raabe, D., Jovicevic-Klug, M., Ponge, D., Gramlich, A., Kwiatkowski da Silva, A., Grundy, A. N., Springer, H., Souza Filho, I., Ma, Y. Circular steel for fast decarbonization:
thermodynamics, kinetics, and microstructure behind upcycling scrap into high-performance sheet steel. Annual Review of Materials Research 54 (2024) 247-297.
- Nakamura, S., Kondo, Y., Nakajima, K., Ohno, H., Pauliuk, S. Quantifying recycling and losses of Cr and Ni in steel throughout multiple life cycles using MaTrace-alloy. Environmental
Science and Technology 51 (2017) 9469-9476.
- Ohno, H., Matsubae, K., Nakajima, K., Kondo, Y., Nakamura, S., Nagasaka, T. Toward the efficient recycling of alloying elements from end of life vehicle steel scrap. Resources,
Conservation and Recycling 100 (2015) 11-20.
- Ohno, H., Matsubae, K., Nakajima, K., et al. Optimal recycling of steel scrap and alloying elements: input-output based linear programming method with its application to end-of-life
vehicles in Japan. Environmental Science and Technology 51 (2017) 13086-13094.
- Daigo, I., Fujimura, L., Hayashi, H., Yamasue, E., Ohta, S., et al. Quantifying the total amounts of tramp elements associated with carbon steel production in Japan. ISIJ International
57 (2017) 388-393.
- Panasiuk, D., Daigo, I., Hoshino, T., et al. International comparison of impurities mixing and accumulation in steel scrap. Journal of Industrial Ecology 26 (2022) 1040-1050.
- Andrews, K. W. Empirical formulae for the calculation of some transformation temperatures. Journal of the Iron and Steel Institute 203 (1965) 721-727.
- Raabe, D., Tasan, C. C., Olivetti, E. A. Strategies for improving the sustainability of structural metals. Nature 575 (2019) 64-74.
- Yang, C., Peng, B., Sun, B., Tao, Q., Zeng, Y., Zhang, L., Shu, D., Lu, J., Raabe, D., Han, L., Wei, Y. From scrap to prime: designing high-performance alloys from dirty feedstocks with
machine learning. Science Advances 12 (2026) eaeg9183.
- Harper, G., Sommerville, R., Kendrick, E., et al. Recycling lithium-ion batteries from electric vehicles. Nature 575 (2019) 75-86.
- Xu, C., Dai, Q., Gaines, L., Hu, M., Tukker, A., Steubing, B. Future material demand for automotive lithium-based batteries. Communications Materials 1 (2020) 99.
- Li, W., Erickson, E. M., Manthiram, A. High-nickel layered oxide cathodes for lithium-based automotive batteries. Nature Energy 5 (2020) 26-34.
- Zhang, S. S. Problems and their origins of Ni-rich layered oxide cathode materials. Energy Storage Materials 24 (2020) 247-254.
- Meshram, P., Pandey, B. D., Mankhand, T. R. Extraction of lithium from primary and secondary sources by pre-treatment, leaching and separation: a comprehensive review. Hydrometallurgy
150 (2014) 192-208.
- Botelho Junior, A. B., Stopic, S., Friedrich, B., Tenorio, J. A. S., Espinosa, D. C. R. Cobalt recovery from Li-ion battery recycling: a critical review. Metals 11 (2021) 1999.
- Cheng, C. Y. Purification of synthetic laterite leach solution by solvent extraction using D2EHPA. Hydrometallurgy 56 (2000) 369-386.
- Ritcey, G. M. Solvent extraction in hydrometallurgy: present and future. Tsinghua Science and Technology 11 (2006) 137-152.
- Zheng, X., Gao, W., Zhang, X., et al. Spent lithium-ion battery recycling: reductive ammonia leaching of metals from cathode scrap by sodium sulphite. Waste Management 60 (2017)
680-688.
- Wu, C., Hu, J., Ye, L., et al. Direct regeneration of spent Li-ion battery cathodes via chemical relithiation reaction. ACS Sustainable Chemistry and Engineering 9 (2021)
16384-16393.
- Marafi, M., Stanislaus, A. Spent hydroprocessing catalyst management: a review. Resources, Conservation and Recycling 53 (2008) 1-26.
- Innocenzi, V., Ippolito, N. M., De Michelis, I., et al. Hydrometallurgical recovery of nickel and rare earths from spent nickel metal hydride batteries. Journal of Power Sources 211
(2012) 184-191.
- Srichandan, H., Mohapatra, R. K., Parhi, P. K., Mishra, S. Bioleaching approach for extraction of metal values from secondary solid wastes: a critical review. Hydrometallurgy 189 (2019)
105122.
- Reuter, M. A., van Schaik, A., Gutzmer, J., Bartie, N., Abadias-Llamas, A. Challenges of the circular economy: a material, metallurgical, and product design perspective. Annual Review
of Materials Research 49 (2019) 253-274.
- Eckelman, M. J., Ciacci, L., Kavlak, G., Nuss, P., Reck, B. K., Graedel, T. E. Life cycle carbon benefits of aerospace alloy recycling. Journal of Cleaner Production 80 (2014)
38-45.
- Reed, R. C. The Superalloys: Fundamentals and Applications. Cambridge University Press (2006).
- Pollock, T. M., Tin, S. Nickel-based superalloys for advanced turbine engines: chemistry, microstructure and properties. Journal of Propulsion and Power 22 (2006) 361-374.
- Donachie, M. J., Donachie, S. J. Superalloys: A Technical Guide, 2nd edition. ASM International (2002).
- Kwiatkowski da Silva, A., Souza Filho, I. R., Lu, W., et al. A sustainable ultra-high strength Fe18Mn3Ti maraging steel through controlled solute segregation and alpha-Mn
nanoprecipitation. Nature Communications 13 (2022).
- Sun, B., Kwiatkowski da Silva, A., Wu, Y., Ma, Y., Chen, H., Scott, C., Ponge, D., Raabe, D. Physical metallurgy of medium-Mn advanced high-strength steels. International Materials
Reviews 68 (2023) 786-824.
- Cann, J. L., De Luca, A., Dunand, D. C., et al. Sustainability through alloy design: challenges and opportunities. Progress in Materials Science 117 (2021) 100722.
- Gavriljuk, V. G., Berns, H. High Nitrogen Steels. Springer (1999).
- Basak, C. B., Meduri, A., Hari Babu, N. Influence of Ni in high Fe containing recyclable Al-Si cast alloys. Materials and Design 182 (2019) 108017.
- Raabe, D., Ponge, D., Uggowitzer, P. J., et al. Making sustainable aluminum by recycling scrap: the science of dirty alloys. Progress in Materials Science 128 (2022) 100947.
- Nutor, R. K., Ruffino, M., Cohen Miles, A., et al. Enabling circularity of copper through nanoscale impurity control. Acta Materialia 297 (2025) 121373.
- Yang, K., Wang, Y., Guo, M., et al. Recent development of advanced precipitation-strengthened Cu alloys with high strength and conductivity: a review. Progress in Materials Science 138
(2023) 101141.
- Stinn, C., Allanore, A. Selective sulfidation of metal compounds. Nature 602 (2022) 78-83.
- Allanore, A., Yin, L., Sadoway, D. R. A new anode material for oxygen evolution in molten oxide electrolysis. Nature 497 (2013) 353-356.
- Sabat, K. C. Production of nickel by cold hydrogen plasma. Plasma Chemistry and Plasma Processing 41 (2021) 1329-1345.
- Du Plessis, C. A., Slabbert, W., Hallberg, K. B., Johnson, D. B. Ferredox: a biohydrometallurgical processing concept for limonitic nickel laterites. Hydrometallurgy 109 (2011)
221-229.
- Hallberg, K. B., Grail, B. M., du Plessis, C. A., Johnson, D. B. Reductive dissolution of ferric iron minerals: a new approach for bio-processing nickel laterites. Minerals Engineering
24 (2011) 620-624.
- Hosseini Nasab, M., Noaparast, M., Abdollahi, H., Amoozegar, M. A. Indirect bioleaching of Co and Ni from iron rich laterite ore using metabolic carboxylic acids. Hydrometallurgy 193
(2020) 105309.
- Rodrigues, F., Pickles, C. A., Peacey, J., Elliott, R., Forster, J. Factors affecting the upgrading of a nickeliferous limonitic laterite ore by reduction roasting, thermal growth and
magnetic separation. Minerals 7 (2017) 176.
- Oliveira, V. de A., Rodrigues, M. L. M., Leao, V. A. Reduction roasting and bioleaching of a limonite ore. Hydrometallurgy 200 (2021) 105554.
- Binnemans, K., Jones, P. T. Solvometallurgy: an emerging branch of extractive metallurgy. Journal of Sustainable Metallurgy 3 (2017) 570-600.
- Sommerfeld, M., Friedmann, D., Kuhn, T., Friedrich, B. Zero-waste: a sustainable approach on pyrometallurgical processing of manganese nodule slags. Minerals 8 (2018) 544.
- Friedmann, D., Friedrich, B. Optimized slag design for maximum metal recovery during the pyrometallurgical processing of polymetallic deep-sea nodules. In Molten Slags, Fluxes and Salts
(2016) 97-104.
- Beolchini, F., Becci, A., Barone, G., et al. High fungal-mediated leaching efficiency of valuable metals from deep-sea polymetallic nodules. Environmental Technology and Innovation 20
(2020) 101037.
- Wei, Y., Peng, B., Xie, R., et al. Deep active optimization for complex systems. Nature Computational Science 5 (2025) 801-812.
- Gaines, L., Sullivan, J., Burnham, A., Belharouak, I. Life-cycle analysis for lithium-ion battery production and recycling. Transportation Research Board 90th Annual Meeting
(2011).